James' 2.0 8v Diplomat

Show off your pride and joy! All Mk3 Cavaliers are welcome (please post only one thread per car)
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

It's difficult to tell the exact diameter with all the surface rust and without proper equipment.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Right, just been down to see the very helpful parts chap at SLM Vauxhall.

Amazingly both of the rear ARB bushes are still available and at only £1.99 for the end bushes and £3.01 for the middle ones (17mm).
Only snag is the end ones are only available as packs of 5, which is ok. In fact I bought 2 packs :D - they fit all of my Cavs, I'm bound to need them eventually!
Plus £19.99 for 10 is a damn good deal compared to £25 just for those 2 on eBay.

They are on order and should arrive on Thursday.
Just need to get some front ARB bushes and then I'll have all the parts I need.

Edit - Just seen the front bushes I need listed on AutoVaux for just £2 each for genuine GM parts.
Now I've got everything I need. Just need to wait for all of it to arrive now.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

At long last, I had a big box of goodies arrive through the post today.
Inside were my Bilsten B4 shock absorbers and, fresh from the factory, my Eibach pro kit springs.

Image

Image

Image


Should go nicely with this mega haul of Genuine componentry:

Image


Rubber spring seats top and bottom:

Image


Rear ARB bushes, all new from Vauxhall:

Image


Front ARB bushes of varying quality:

Image


Odd thing about these is they were packaged as 90447867 parts (which is a newer part number), yet the parts themselves were stamped with the older 90304225 number. :scratch
Oh well, both numbers are right for my Diplomat.

Image


Anyway, I bought 4 as I'm planning to update the suspension on the CD manual after this and it uses the same part.
All 4 were bought from genuine parts search but they came from different suppliers and have all spent years sitting on shelves by the looks of them. The rubber is still good though.


Febi top mounts:

Image


Delphi steering arms, bolts and rod ends:

Image


Can't wait to get it all fitted now! :cheers
User avatar
Robsey
Club Admin
Posts: 10569
Joined: Fri Dec 12, 2008 1:42 pm
Location: East Manchester

Re: James' 2.0 8v Diplomat

Post by Robsey »

It reminds me of my desk at work in June last year.
Loads and loads of new parts.

I can guarantee that you will feel a massive difference when you have fitted this little lot.

It will be interesting how many bushes and spacers etc; are mis-aligned when you remove them from your front suspension legs.

My alignment marks, notches and ribs were all over the place despite being untouched since leaving the factory.

Amazingly Haynes is quite accurate and useful in this area.

By the way. The tubular nut that holds the front damper in will need a good bench vice or a 60mm spanner to remove it.

And the top mounts.... did you get the bearing with it too. Again, Haynes will advise the correct orientation of the bearing during assembly.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

I suspect that everything is out by a mile on this car.
I don't know when the tracking was last done as the track rods have completely seized.
My new tyres have already started to get the tell tale uneven wear in the inside edge. That's the main reason for wanting this all done really, that and the broken spring.

Yes, I did get the bearing with the top mounts, it's in the box.
cavalier1990
Registered user
Posts: 1460
Joined: Wed Jun 29, 2011 9:15 pm
Location: Paisley, Scotland

Re: James' 2.0 8v Diplomat

Post by cavalier1990 »

Regarding the part numbers for the ARB bushes James it's a typical VX change of number. You can see here

http://ecat24.com/opel/catalog/part/1/39/420/4348/9967/

Look for any of the 90304225 and it says e.g: BEARING,FRONT STABILIZER BAR (FOR 22MM) (EXCEPT FOUR WHEEL DRIVE) (NLS.- USE 90447867 3 50 078)

I just replaced my top mount rubbers too. On the face of it they didn't look worn but if you put them side by side they difference was astonishing. They gap from top to the inner dish was a lot less than the new ones so they were flattened from years of use. Look at the differences, especially how far up the top plate is compared to the new one on the left:

Image

Image

Image

In hindsight I wish I had sourced all the other parts new as they all looked a tad worn or just perished.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Wow, that does look squashed. :shock:

Did you notice much difference once you fitted the new ones?
User avatar
Robsey
Club Admin
Posts: 10569
Joined: Fri Dec 12, 2008 1:42 pm
Location: East Manchester

Re: James' 2.0 8v Diplomat

Post by Robsey »

Regardless of the squashed-ness of them,
take a look at the severe cracks in the middle photo.

These parts do take a lot of hammer and suffer cracking and the strut top spindles have been known to burst through completely.

Both of mine were on the verge of bursting through with a lot of knocking noises on uneven surfaces.

Image
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Yes I saw the cracks, nasty.
I wonder what mine are going to be like now!
cavalier1990
Registered user
Posts: 1460
Joined: Wed Jun 29, 2011 9:15 pm
Location: Paisley, Scotland

Re: James' 2.0 8v Diplomat

Post by cavalier1990 »

James McGrath wrote:Wow, that does look squashed. :shock:

Did you notice much difference once you fitted the new ones?
Yes a lot, car a lot tighter, steering much better, stable on the mway etc.

If you haven't fitted yet measure the gap between the bodywork strut top and the little round plate below the top nut and then measure after fitting. The big gap is the strut pushing up through the worn rubber.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Just thinking, should I replace the wheel bearings too?
None of them are giving me any problems, no noise etc. but if I'm going to be replacing all the other componentry would it not be good practice to do so?
User avatar
Lowrider Dave
Club Admin
Posts: 2993
Joined: Wed Dec 22, 2010 10:00 am
Location: Southampton
Contact:

Re: James' 2.0 8v Diplomat

Post by Lowrider Dave »

That's a good haul of parts!
Lowrider Dave.

Archer 2.0 GLS
User avatar
Robsey
Club Admin
Posts: 10569
Joined: Fri Dec 12, 2008 1:42 pm
Location: East Manchester

Re: James' 2.0 8v Diplomat

Post by Robsey »

If you are stripping the legs anyway, then I would change the bearings too.

Get a company to let you use their bench press. A doddle of a job.
(Apart from the circlips that look and feel like they are too big, and you struggle like a twonk to get them into the grooves.
But they do fit - honest).

My bearings felt fine and I did not have any adverse noise. But after 250,000 miles, apparently they were completely shot.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Ok, I'll get a new set.
Do you know what parts I'll need Rob? Just the bearings or the hubs too?
cavalier1990
Registered user
Posts: 1460
Joined: Wed Jun 29, 2011 9:15 pm
Location: Paisley, Scotland

Re: James' 2.0 8v Diplomat

Post by cavalier1990 »

James McGrath wrote:Ok, I'll get a new set.
Do you know what parts I'll need Rob? Just the bearings or the hubs too?
Just bearings you'd need. Personally wouldn't touch them if they are ok. If you are getting bearings they are different sizes. I think yours and the 1.8 are the bigger one, 42 mm if I remember rightly, and 37mm or similar for the smaller engine.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Well if it's all being taken apart to renew the rest of the suspension, then I might as well replace the bearings at the same time.
I've no idea how long they have been on there so at least I'll know that they are new and shouldn't give me any trouble in the future.

4 new Febi bearings have been ordered.
User avatar
Cabletwitch
Registered user
Posts: 292
Joined: Sun Oct 02, 2011 7:18 pm
Location: Woodley, way too close to Reading.

Re: James' 2.0 8v Diplomat

Post by Cabletwitch »

Well, I know who I'll be taking my Cav to if anything breaks now :O)
Never use another Cav driver as guidance to a destination, unless you REALLY want to explore the country.

"Won't SOMEBODY please think of the scones?"

1.7TD Ethos (Slightly broken)
1.8i (Given up, going for parts)
2.0i (WHY won't it work?!)
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Things were all going so well on Thursday.
I had decided to do a coolant change and get rid of the blue coolant that was in there and replace it with some proper GM Dex-cool.

Image


I managed to drain the system, despite the awkward placement of the air con system:

Image


I flushed out both the radiator and the engine block, which were surprisingly clean.
There is some of the flush water, nice and clear with no nasty deposits:

Image


And I even managed to remove the old thermostat with no problems:

Image


The original item was still working as it should:

Image


But I thought it was a good idea to replace it with a new one while I was there:

Image


Finally, I put everything back together and filled the system up:

Image


I started the engine and ran it until it wormed up.
No leaks, and thermostat working perfectly. Hurrah! :cheers

After this successful morning I decided to give the old girl a proper scrub down:


Image

Image

Image

Image


Things were going so well I decided to tempt fate by saying to my neighbour that, for once with this car, nothing had gone wrong.
Oh how wrong I was...
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

10 minuets after that last photo was taken, the Diplomat looked like this:

Image

Image

Image

Image

Image

Image


I was driving thought Robertsbridge high street and noticed there was a car peeping and creeping out of a side turning. I didn't think anything of it as I thought they had already seen me.
Next thing I knew was that there was a loud bang.
They had driven right into the side of me.

No one was hurt and the person who hit me was very apologetic and admitted liability straight away.
I am currently waiting for someone to come round and asses the damage. I suspect they will take one look at it and say it is uneconomical to repair but hey ho. Hopefully they will offer me a good price for it.

I've already been to see my usual bodywork man who says he can repair it if I can find 2 new doors.
So hopefully this is not the end of my Diplomat and it will be fixed.
Mazza
Registered user
Posts: 258
Joined: Thu Nov 03, 2016 11:00 am

Re: James' 2.0 8v Diplomat

Post by Mazza »

Ouch! And I was thinking what a great looking car.... or was.

Hope all works out...
User avatar
Cabletwitch
Registered user
Posts: 292
Joined: Sun Oct 02, 2011 7:18 pm
Location: Woodley, way too close to Reading.

Re: James' 2.0 8v Diplomat

Post by Cabletwitch »

Jeez, that's not good... damn shame to boot, she was looking very tidy before that. Keep us informed of the progress in repairing her!
Never use another Cav driver as guidance to a destination, unless you REALLY want to explore the country.

"Won't SOMEBODY please think of the scones?"

1.7TD Ethos (Slightly broken)
1.8i (Given up, going for parts)
2.0i (WHY won't it work?!)
User avatar
Mk3alan
Registered user
Posts: 632
Joined: Sun Mar 09, 2014 8:40 pm

Re: James' 2.0 8v Diplomat

Post by Mk3alan »

Sorry to hear that, makes you feel sick hope it works out for you.

Alan
User avatar
Robsey
Club Admin
Posts: 10569
Joined: Fri Dec 12, 2008 1:42 pm
Location: East Manchester

Re: James' 2.0 8v Diplomat

Post by Robsey »

Blimey O'Reilly !!

Prior to the new damage the car was looking in brilliant condition. Hopefully the assessor will okay the repairs based upon that fact, rather than just writing the old girl off.

Doors are one thing... the bump strips will be very tricky to source.

I hope the news is good... there have been a lot of Cavs being moved on recently due to being beyond economical repair.
iangsi
Club Admin
Posts: 1709
Joined: Tue Jan 19, 2010 4:58 pm
Location: Bromley, Kent.

Re: James' 2.0 8v Diplomat

Post by iangsi »

Holy shit what hit you a tractor :o scuffed your alloy wheel as well.
User avatar
James McGrath
Club Admin
Posts: 2894
Joined: Tue Aug 11, 2009 11:35 am
Location: East Sussex

Re: James' 2.0 8v Diplomat

Post by James McGrath »

Thanks for your well-wishes guys. I'm sure this isn't the end of my Diplomat, just a setback.
The old girl kept me safe and I've never been more thankful of those side impact bars in the doors, they did their job well.
I hate to think what the damage would have been like had I been driving the CD auto which, being a pre-facelift, doesn't have them.

iangsi wrote:Holy shit what hit you a tractor :o scuffed your alloy wheel as well.

It was a new ford focus.
I think I came off worse but there was damage to it's front bumper, headlight and wing.
My alloy is actually ok. It looks bad in the photo but it's actually paint that has come from the other car. Luckily the alloy itself isn't scratched and I've managed to get most of it off.

Robsey wrote: Doors are one thing... the bump strips will be very tricky to source.

I hope the news is good... there have been a lot of Cavs being moved on recently due to being beyond economical repair.

There is a Cavalier on eBay at the moment that has the correct door strips on it already. It's also in the same colour which is a bonus. Amazingly, both of my eclectic windows still work and the door cards are intact so hopefully I can just swap those over into the new doors
Only problem is it's about 230 miles away from me:

http://www.ebay.co.uk/itm/VAUXHALL-CAVA ... Sw33hZAfvO


The person who was driving was actually a friend of the family. She's going through some rough times at the moment as her husband has cancer. So I feel sorry for her too.
Post Reply